Flooring - Solvent Base - Wood Filler Base

  • Product Description
  • Physical Properties
  • Application Data
  • Directions for Use
  • Technical Literature

Product Code:

1C70

Product Description and Uses:

Schwartz Wood Filler Base is used to bind sawdust or wood flour.

Used for filling small gaps, crevices and holes in parquet and other hardwood floor surfaces prior to applying Schwartz Premium or Classic Polyurethane wood floor finishes.

Product Advantages:

1. Easy to blend.

2. Excellent filling and adhesion.

3. Easy to sand.

4. Fast drying.

5. Designed for trowel application.

Standard Container Sizes

18.9 Litre Pail

Physical:

Viscosity:

55 sec. #4 Ford Cup

Flash Point

- 18°C

Weight Solids:

18% +/- 2%

Density:

0.901 g/ml

Shelf Life:

2 years unopened.

Environmental Information:

VOC: max 300 g/L (as applied following minimum blending ratio of 1.5/1 parts of sawdust / 1C70 (CEPA Compliant)

Suggested Uses:

Used for filling small gaps, crevices and holes in parquet and other hardwood floor surfaces.

Mixing Instructions:

1 part 1C70 for every 1.5 parts sawdust / wood flour

Recommended System:

NA

Application Tools:

Trowel

Coverage:

400 sq ft/gal or 37 sq m/3.78 L (4 mils wet film)

Dry Time:

30 minutes at ambient conditions.

CAUTION: Cold temperature, high humidity, or lack of airflow will prolong dry times.

Recoat time:

NA

Clean-up Solvent:

4T100 Lacquer Thinner

Reducer:

NA

Retarder:

NA

Pot Life:

NA

Surface Preparation:

Surface to be coated must be clean, dry and contaminant-free. Follow NOFMA Guidelines for sanding.

Old Floors:

Use medium grit (50, 60, 80) sandpaper to remove old finish or wax, and to level the floor.

Depending on the build-up of old finish start with a coarse grit (36, 40 ) sandpaper then move to a medium grit.

Finish-off with fine grit (80, 100, 120, 150) sandpaper for final cut.

New Floors:

Use medium grit to level floor.

Vacuum and tack with lint-free towel dampened with water or mineral spirits.

Ambient Conditions:

  1. Use only when ambient conditions are 18°C to 30°C and RH = 40-60%.
  2. Wood moisture content must be between 6 - 10%.

Application:

Using a separate container premix Wood Filler Base with saw dust or wood flour.

Combine 1.5 parts of sawdust or wood flour with 1 parts of Wood Filler Base and mix well

DO NOT USE any mechanical mixer i.e. drill.

MIX BY HAND - DO NOT MIX WITH METAL OBJECTS.

Absorption is dependent on the species of wood sawdust or wood-flour, therefore it may be necessary to adjust filler and mix consistency accordingly.

Starting at the furthest corner of the room, pour premixed filler and spread with a non-spark trowel.

Trowel filler mixture into crevices, large gaps or holes.

Do not exceed gaps over 3mm.

Allow to dry minimum of 30 minutes.

Finish-off with fine grit (80, 100, 120) sandpaper.

Vacuum and tack with lint-free towel, dampened with water or mineral spirits.

Storage:

Store indoor at room temperature, away from heat, ignition sources, open flames and direct sunlight.

Warning:

AVOID sparking, use non-sparking tools.

Avoid open flames, turn off all pilot lights, ensure that work area is properly ventilated.

Soiled rags and waste products may contain combustible liquids or vapours, dispose in accordance with local regulations.

Refer to MSDS for information on safe use of this product.


For SDS and Technical Literature please call or e-mail us at;


Tel: 905-683-0411 | Toll Free: 1-866-519-9674
Email: info@schwartzchem.com