Millwork / Furniture - Pre-Catalyzed Lacquer Systems - Finishes

  • Product Description
  • Physical Properties
  • Application Data
  • Directions for Use
  • Technical Literature

Product Codes:

93C90 - Gloss SS Pre-Catalyzed Lacquer

93C50 - Semi-Gloss SS Pre-Catalyzed Lacquer

93C35 - Satin SS Pre-Catalyzed Lacquer

93C21 - Matt SS Pre-Catalyzed Lacquer

Product Description and Uses:

Schwartz Pre-Catalyzed Lacquer is a one component, pre-catalyzed lacquer developed for furniture and millwork applications providing good protection properties and aesthetics to any interior wood surface.

Product Advantages:

1. Very good durability and abrasion resistance

2. Good resistance to common household chemicals

3. Excellent film build

4. Very good flow and leveling

5. Good clarity

6. Fast drying

7. Accents wood grain

Standard Container Sizes

205L Drum

18.9 Litre Pail

Physical:

Viscosity:

33-37 sec. (#4 Ford Cup)

Flash Point:

2°C

Weight Solids:

23 - 26%

Density:

0.94 – 0.96 g/ml

Appearance:

Gloss - clear

Semi-Gloss, Satin, Matt, Flat Sheen Gloss-90+, Semi-Gloss-50, Satin-35, Matt-20 - milky liquid

Shelf Life:

1 year unopened

Environmental Information:

VOC: max 700 g/L

Suggested Uses:

Schwartz Pre-Cat Lacquer is used for finishing interior wood surfaces.

Mixing Instructions:

Mix well before use.
Avoid excessive stirring or shaking as this can cause bubbles to form.

Recommended System:

Schwartz Pre-Cat Lacquer is designed as a self-sealing finish over bare wood.
For best results, seal with 1 coat of 92C1 Pre-Cat Sanding Sealer followed by 2 even coats of Schwartz Pre-Cat Lacquer at 3-5 mils wet film thickness per coat.
Always allow to dry and scuff sand between coats.

Application Tools:

Apply by spray.

Coverage:

534 sq ft/gal (3 mils Wet Film); 320 sq ft/gal (5 mils Wet Film)

Dry Time:

Tack Free Time = 15 - 20 minutes.
To Sand = 2 - 2.5 hours.
To Recoat = 2 - 2.5 hours.

25C, 60% RH - cold temperature and high humidity can cause prolonged dry times.

Recoat time:

2 - 2.5 hours (25C, 60% RH)

Clean-up Solvent:

4T100 Lacquer Thinner.

Reducer:

4T100 Lacquer Thinner.

Retarder:

4T175

Pot Life:

NA

Surface Preparation:

Surfaces must be clean, dry and contaminant-free.

Sand wood with 150-grit sandpaper before staining or coating.

Remove all dust.

When sealer or topcoat is sanded, always apply succeeding coat within 8 hours of sanding.

Sand between coats with 280 - 320 grit sandpaper.

Ambient Conditions:

Use only when ambient conditions are 18°C to 30°C and RH= 40-60%.

Finish temperature must be > 15°C.

Wood moisture content must be between 6 - 10%

Application:

Following surface preparation; apply by spray.

Check with equipment manufacturer for settings to achieve the correct atomization.

For best results, seal bare wood with 1 coat of 92C1 Pre-Cat Sanding Sealer followed by 2 even coats of Schwartz Pre-Cat Lacquer at 3-5 mils wet film thickness per coat.

Always allow to dry and scuff sand between coats with 280-320 grit sandpaper.

Film build of entire system must not exceed 5 mils dry film thickness.

Storage:

Store indoors away from heat, ignition source, wet conditions and direct sun.

Warning:

AVOID sparking - use non-sparking tools.

Avoid open flames, turn off all pilot lights and ensure that work area is properly ventilated.

Soiled rags and waste products may contain combustible liquids or vapours, dispose in accordance with local regulations.

Refer to MSDS for information on safe use of this product.


For SDS and Technical Literature please call or e-mail us at;


Tel: 905-683-0411 | Toll Free: 1-866-519-9674
Email: info@schwartzchem.com