Flooring - Solvent Base - Low VOC Floor Sanding Sealer

  • Product Description
  • Physical Properties
  • Application Data
  • Directions for Use
  • Technical Literature

Product Code:

1C360

Product Description and Uses:

1C360 is a lacquer base sealer formulated to seal hardwood surfaces.

Easy to apply and provides a superior base coat for Polyurethane topcoats.

Product Advantages:

1. Fast dry.

2. Stearrated to provide smoother sanding.

3. Seals open and closed grain wood.

4. High solids.

5. Excellent penetration.

Standard Container Sizes

18.9 Litre Pail

Physical:

Viscosity:

60 - 70 sec #4 Ford Cup

Flash Point

-18°C

Weight Solids:

26.5 to 28.5%

Density:

0.925 g/ml

Sheen:

Gloss

Appearance:

Hazy liquid

Shelf Life:

2 years unopened

Environmental Information:

VOC: max 550 g/L (CEPA Compliant)

Suggested Uses:

Used to seal interior commercial, residential and gymnasium hardwood floors.

Mixing Instructions:

Avoid excessive stirring or shaking as this can cause bubbles to form. (Do not shake in paint shaker.)

Recommended System:

Use with Schwartz Premium Polyurethane Floor Finishes.

Apply 1 coat (4 mils wet film) to most wood species.

For porous wood surfaces, apply 2 coats of Schwartz Wood Floor Sealer.

Application Tools:

Apply Floor Finish using, T-bar, wood block mop or roller with synthetic pad, lambswool or synthetic bristle brush.

Coverage:

400 sq ft/gal or 37 sq m/3.78 L (4 mils wet film)

Dry Time:

Tack free in15 minutes (25C, 60% RH).

Drys hard in 1 hr (25C, 60% RH).
CAUTION: Cold temperature, high humidity, or lack of airflow will prolong dry times.

Recoat time:

1 hour (25C, 60% RH)

Clean-up Solvent:

4T100 Lacquer Thinner

Reducer:

NA

Retarder:

NA

Pot Life:

NA

Surface Preparation:

Surface to be coated must be clean, dry and contaminant-free. Follow NOFMA Guidelines for sanding.

Old Floors:

  1. Use medium grit (50, 60, 80) sandpaper to remove old finish or wax, and to level the floor.
  2. Depending on the build-up of old finish start with a coarse grit (36, 40 ) sandpaper then move to a medium grit .
  3. Finish-off with fine grit (80, 100, 120, 150) sandpaper for final cut.
  4. New Floors:
  5. Use medium grit to level floor and finish-off with fine grit sandpaper.
  6. Vacuum and tack with lint-free towel dampened with water or mineral spirits.

Ambient Conditions:

  1. Use only when ambient conditions are 18°C to 30°C and RH= 40-60%.
  2. Wood moisture content must be between 6 - 10%.

Application:

  1. Following surface preparation, apply one coat of sealer with recommended applicator.
  2. For porous surfaces, apply two (2) coats of sealer.
  3. Always work with the grain.
  4. Apply continuously and always start and stop where the floor and the wall intersect.
  5. Let dry 1 hour.
  6. Buff with used 120 grit screen or maroon pad.
  7. Vacuum all dust and tack with lint-free towel dampened with water or mineral spirits.
  8. Let dry completely.
  9. Always buff, vacuum, tack and dry floor in between coats.

Storage:

Store indoor at room temperature, away from heat, ignition sources, open flames and direct sunlight.

Warning:

  1. AVOID sparking, use non-sparking tools.
  2. Avoid open flames, turn off all pilot lights, ensure that work area is properly ventilated.
  3. Soiled rags and waste products may contain combustible liquids or vapours, dispose in accordance with local regulations.
  4. Refer to MSDS for information on safe use of this product.

For SDS and Technical Literature please call or e-mail us at;


Tel: 905-683-0411 | Toll Free: 1-866-519-9674
Email: info@schwartzchem.com